废气设备巡查制度(废气设备巡查制度及流程)本页面通过数据整理汇集了废气设备巡查制度(废气设备巡查制度及流程)相关信息，下面一起了解一下。

废气设备巡查制度(废气设备巡查制度及流程)

废气设备巡查制度

鑫源环保设备有限公司带大家了解废气治理机器设备运行前的提前准备:

1.检查窑尾袋收尘空气压缩的压力是不是一切正常，汽缸、煤气发生炉工作压力能否做到标准值，每个人孔门是不是关掉及时，有无透风。

2.检查各机器设备地脚丝有无松脱，人孔门是不是关紧，各开料口有无跑料或阻塞。

3.各运转机器设备周边有无防碍物，靠背轮、传动齿轮保护罩是不是无恙。

3.与中控台联络对比各仪表盘意见反馈数据信号是不是相符合。

4.检查窑尾引风机前后左右轴承油位，各拉锁机绞刀下加料器进库斗提机减速器油位，传动系统传动链条润化状况，均化库顶袋收尘离心风机连轴器油位。

5.检查有机废气处理设备的窑尾引风机轴承冷却循环水工作压力及闸阀电源开关状况。

5.检查增压水泵进出口贸易闸阀是不是恰当，储水箱水位线在1.0米之上。

6.在现场具有出发运送到韶山标准后，将锁匙电源开关打成中控台部位，与中控台联络是不是有备妥并告知组长、电气设备工作人员到当场，提前准备启运。

2.废气处理设备的巡检

1.检查窑尾引风机轴承、进库斗提机减速器以及其他锅炉辅机减速器油位转变及其窑尾引风机轴承冷却循环水工作压力。

2.纪录对比窑尾引风机轴承及电动机轴承.电机定子溫度，当产生大幅变动时紧急停窑尾引风机。(离心风机轴承:75℃警报80℃跳停)

3.进库斗提机传动带有无方向跑偏。

4.拉锁机传动链条有无异响.方向跑偏，传动齿轮有无冒牙或破裂。

5.加湿塔绞刀尼龙棒是不是一切正常，开料是不是有湿块。

6.库顶袋收尘运作是不是一切正常，有无起烟，料仓有无跑料。

7.窑尾袋收尘压力差增大时，废气治理厂家立即检查空气压缩工作压力及脉冲电磁阀有无漏汽，气压表能否一切正常。

8.窑停时，可以恰当电源开关供电闸阀。

9.星型下加料器是不是卡住，脱硝。

Xinyuan environmental protection equipment Co., Ltd. takes you to know the preparation in advance before the operation of waste gas treatment machinery and equipment: < / P > < p > 1. Check whether the pressure of dust collection air compression in the kiln tail bag is normal, whether the working pressure of the cylinder and gas generator can meet the standard value, whether each manhole door is closed in time, and whether there is ventilation < p > 2. Check whether the anchor wire of each machine and equipment is loose, whether the manhole door is tightly closed, and whether the tapping openings are free of material running or blocking < p > 3. Check whether there are obstacles around the running machines and equipment, and whether the coupling and transmission gear protective covers are in good condition < p > 3. Contact the central console to compare whether the feedback data signals of various instrument panels are consistent < p > 4. Check the oil level of the front and rear left and right bearings of the induced draft fan at the end of the kiln, the oil level of the lower cutter feeder of each locker, the reducer of the bucket elevator, the lubrication of the drive chain of the drive system, and the oil level of the coupling of the centrifugal fan for dust collection at the top of the homogenizing silo < p > 5. Check the working pressure of cooling circulating water for the bearing of induced draft fan at the kiln end of the organic waste gas treatment equipment and the power switch status of the gate valve < p > 5. Check whether the import and export trade gate valve of booster pump is proper, and the water level of the storage tank is above 1.0m < p > 6. After the site has the standard for departure to Shaoshan, turn the key power switch to the central console, contact the central console to see if it is ready, and inform the team leader and electrical equipment staff to arrive at the site to prepare for departure in advance < p > 2. Patrol inspection of waste gas treatment equipment < / P > < p > 1. Check the oil level change of the induced draft fan bearing at the end of the kiln, the reducer of the bucket elevator and other boiler auxiliary machine reducers, and the working pressure of the cooling circulating water of the induced draft fan bearing at the end of the kiln < p > 2. Record and compare the induced draft fan bearing and motor bearing at the kiln end When the temperature of the motor stator changes greatly, the induced draft fan at the kiln end will be stopped in an emergency. (bearing of centrifugal fan: alarm at 75 ℃ and trip at 80 ℃) < / P > < p > 3. The drive of the bucket elevator entering the warehouse has non directional deviation < p > 4. Check whether the drive chain of the locking machine has abnormal noise, direction deviation, and whether the drive gear has teeth or cracks < p > 5. Check whether the nylon rod of the humidifying tower cutter is normal and whether there is wet block during blanking < p > 6. Whether the dust collection operation of the bag on the top of the warehouse is normal, whether there is smoke, and whether there is material leakage in the silo < p > 7. When the dust collection pressure difference of the kiln tail bag increases, the waste gas treatment manufacturer should immediately check the working pressure of the air compression and the pulse solenoid valve for steam leakage, and whether the barometer is normal < p > 8. When the kiln stops, the gate valve can be powered by appropriate power switch < p > 9. Whether the star shaped lower feeder is stuck or not, denitration

废气设备巡查制度(废气设备巡查制度及流程)相关信息请关注本文章，本站内容仅作为做为展示，不参与任何商品交易。