欢迎您访问章工恒立官方网站!生产催化燃烧废气处理环保设备,是专业的催化燃烧设备厂家.

章工恒立环境科技有限公司

专注废气处理一站式解决方案服务商

联系我们
二维码 章工恒立

联系电话:13964187654

联系地址:山东省济南市章丘区绣惠街道茂李工业园

位置:网站首页>新闻资讯>废气处理设备安装的知识要点(废气处理设备安装的知识要点是什么)

废气处理设备安装的知识要点(废气处理设备安装的知识要点是什么)

文章作者:章工恒立 发布时间:2022-09-06 16:42:24 浏览次数:0

废气处理设备安装的知识要点(废气处理设备安装的知识要点是什么)本页面通过数据整理汇集了废气处理设备安装的知识要点(废气处理设备安装的知识要点是什么)相关信息,下面一起了解一下。

废气处理设备安装的知识要点(废气处理设备安装的知识要点是什么)

废气处理设备安装的知识要点

废气处理设备安装的专业知识也许多,像烟囱高度的测算,必须考虑到哪些方面?又必须采用哪些公式计算,不清楚大伙儿掌握是多少,鑫源环保设备有限公司为大Joan介绍一下工业废气除灰烟囱高度怎么计算。

1.有关工业废气除灰烟囱高度蔓延主要参数与上端逆温的影响

烟囱高度测算中,óz/óy一般取0.5~1.0,其值尺寸对烟囱高度影响非常大。

上边的工业废气除灰烟囱高度公式计算全是在溫度层结同样时导出来的。针对高而强的热原,务必考虑到上端逆温的影响。科学研究结果显示,当合理源高H相当于混和层薄厚D时,路面浓度值相当于一般状况下的2倍。若按此标准设计方案,烟囱高度将大大增加。因而,废气治理厂家为确保安全性,解决混和层薄厚以及发生頻率作调研,以绕开合理源高与发生頻率较大或较高的混和层薄厚相同的情况。在逆温层较低时,很多状况下则规定合理高度能打破逆温层。

2.有关防止工业废气除灰烟气下洗或下移

为了更好地防止烟气下洗,按GB3840-83要求,烟囱高度不可小于它所附设房屋建筑高度的1.5-2.5倍,烟气出口速率U,不可小于烟囱出口高度处均值风力的1.5倍,即规定Us/ú≥1.5。适度提升烟气喷出来速率,有益于提升 驱动力上升。但烟气喷出来速率过高,会在烟气出口迎风面的身后造成负压力区,使一部分气体被卷入烟气中,合理高度反倒减少。为防止此状况,有的烟囱在出口处设定帽舌状水调圆板,圆板向外屈伸的规格Z少相当于烟囱出口的直徑。为提升 喷出来速率,也可将烟囱口设计方案成文丘里管喷头构造,但特别注意摩擦阻力提升不至于过大。

3.有关提升工业废气除灰排量和提升 排烟系统溫度

好多个烟囱分散化排序对上升不好,若配件几个烟源时,要集中化到一个烟囱排出。充分考虑机器设备建成投产有依次,或有一部分停此运作时排烟系统速率不至过低,可选用多筒结合式排出。

烟气溫度对上升有关键实际意义,但专业给烟气加温会扩大财政负担。因而,选用干式除灰,或在烟囱设计方案中尽量避免排烟道及烟囱自身的热损害,都对烟气上升有益。

There is also a lot of expertise in the installation of waste gas treatment equipment. For example, what must be considered in the calculation of stack height? What formulas must be used for calculation? It's not clear how much we know. Xinyuan environmental protection equipment Co., Ltd. will introduce to big Joan how to calculate the height of the industrial waste gas ash removal chimney < p > 1. The influence of the main parameters of the height spread of the industrial waste gas ash removal chimney and the temperature inversion at the upper end < / P > < p > in the calculation of the chimney height, ó Z / ó y is generally taken as 0.5 ~ 1.0, and its value size has a great influence on the chimney height < p > the height formula of the industrial waste gas ash removal chimney above is derived when the temperature stratification is the same. For high and strong pyrogens, the influence of upper temperature inversion must be considered. The scientific research results show that when the reasonable source height h is equivalent to the thickness d of the mixed layer, the pavement concentration value is equivalent to twice that of the general situation. If the scheme is designed according to this standard, the chimney height will be greatly increased. Therefore, in order to ensure safety, the waste gas treatment manufacturers investigated the thickness and occurrence frequency of the mixed layer, so as to avoid the situation that the reasonable source height is the same as the thickness of the mixed layer with higher or higher frequency. When the inversion layer is low, in many cases, a reasonable height is specified to break the inversion layer < p > 2. About preventing the downwash or downward movement of industrial waste gas and ash handling flue gas < / P > < p > in order to better prevent the downwash of flue gas, according to the requirements of gb3840-83, the height of a chimney shall not be less than 1.5-2.5 times of the height of the building attached to it, and the velocity U of flue gas outlet shall not be less than 1.5 times of the average wind force at the height of the chimney outlet, that is, US / ú ≥ 1.5. Moderately increasing the emission rate of flue gas is beneficial to increase the driving force. However, if the exhaust speed of flue gas is too high, a negative pressure zone will be created behind the windward side of the flue gas outlet, so that part of the gas will be drawn into the flue gas, and the reasonable height will be reduced. In order to prevent this situation, some chimneys are provided with a cap tongue shaped water regulating circular plate at the outlet, and the specification Z of the circular plate bent outward is less than the diameter of the chimney outlet. In order to improve the spray rate, the chimney mouth design scheme can also be written into the structure of mound tube nozzle, but special attention should be paid to the increase of friction resistance < p > 3. About raising the ash removal capacity of industrial waste gas and raising the temperature of the smoke exhaust system < / P > < p > the decentralized ordering of many chimneys is not good for rising. If there are several smoke sources, they should be discharged in one chimney. It is fully considered that there is a sequence for the completion and operation of machinery and equipment, or that the rate of smoke exhaust system should not be too low when some of them stop operating here, and multi barrel combined exhaust can be selected < p > the flue gas temperature has a key practical significance to the rise, but professional flue gas heating will increase the financial burden. Therefore, the selection of dry ash removal or the avoidance of thermal damage to the exhaust flue and the chimney itself in the chimney design scheme are beneficial to the rise of flue gas

废气处理设备安装的知识要点(废气处理设备安装的知识要点是什么)相关信息请关注本文章,本站内容仅作为做为展示,不参与任何商品交易。

版权声明:文章来源于网络或用户投稿,转载请注明出处!如有侵权敬请告知!

本文地址:http://www.jnzghl.com/lczs/888.html